Sshd Configuration: Difference between revisions

From NovaOrdis Knowledge Base
Jump to navigation Jump to search
Line 11: Line 11:
=Change the Default Port=
=Change the Default Port=


Uncomment and/or update the default "Port" value in <tt>/etc/ssh/sshd_config</tt>:
Uncomment and/or update the default "Port" value in <code>/etc/ssh/sshd_config</code>:


  #Port 22
  #Port 22

Revision as of 02:45, 30 July 2023

Internal

Overview

The system-wide sshd server configuration file is /etc/ssh/sshd_config (or /etc/sshd_config for cygwin).

man sshd_config

Change the Default Port

Uncomment and/or update the default "Port" value in /etc/ssh/sshd_config:

#Port 22
Port 12345

If the system is SELinux-enabled, you need to confiture SELinux as well, see below.

Change the Default Port on a SELinux System

If SELinux is enabled, you have to tell SELinux about the port change:

semanage port -a -t ssh_port_t -p tcp 12345

Also see How to install SELinux semanage.

Update the Firewall Rules

If iptables is enabled, there is a firewall rule that allows ssh access, and it usually mentions the port. Check if the rule is in place and update it with the new port:

Update SSH iptables rules

Change the Network Interface to Listen On

ListenAddress 192.168.1.10

Prevent from Listening on IPV6

AddressFamily inet

Turn Off Client Name DNS Verification

sshd can be configured with a "UseDNS" option, which specifies whether sshd should look up the remote host name and check that the resolved host name for the remote IP address maps back to the same IP address. The default is “yes” but in some case this causes the initial connection setup to take a long time, so it is best to turn this verification off:

...
UseDNS no
...

The service needs to be restarted after reconfiguration.

root Access

Allow root To Connect with Password

In /etc/ssh/sshd_config:

PermitRootLogin yes

Root access is enabled by default.

Disallow root to Connect

PermitRootLogin no

in /etc/ssh/sshd_config.

Before doing that and rebooting, make sure there's another way to connect to the system (other user, direct access, virsh console, etc).

Allow root Access only with Public Key

In /etc/ssh/sshd_config:

PermitRootLogin prohibit-password

Add the corresponding public key in /root/.ssh/authorized_keys. Note that PubkeyAuthentication must be set to "yes" for access to work.

Logging Verbosity

By default, sshd logs at INFO level:

LogLevel INFO

Options: DEBUG, DEBUG1, DEBUG2, DEBUG3

Increased log output will be available in /var/log/secure.

Allow Port Forwarding

AllowTcpForwarding yes

sshd Security Hardening

Security Hardening

Configuration Reference

ClientAliveInterval

Sets a timeout interval in seconds after which if no data has been received from the client, sshd will send a message through the encrypted channel to request a response from the client. The default is 0, indicating that these messages will not be sent to the client.

Configure ssh Connection Timeout

ClientAliveCountMax

Sets the number of client alive messages which may be sent without sshd receiving any messages back from the client. If this threshold is reached while client alive messages are being sent, sshd will disconnect the client, terminating the session. It is important to note that the use of client alive messages is very different from TCPKeepAlive. The client alive messages are sent through the encrypted channel and therefore will not be spoofable. The TCP keepalive option enabled by TCPKeepAlive is spoofable. The client alive mechanism is valuable when the client or server depend on knowing when a connection has become inactive.

Configure ssh Connection Timeout

UsePrivilegeSeparation

Specifies whether sshd separates privileges by creating an unprivileged child process to deal with incoming network traffic. After successful authentication, another process will be created that has the privilege of the authenticated user. The goal of privilege separation is to prevent privilege escalation by containing any corruption within the unprivileged processes. If UsePrivilegeSeparation is set to "sandbox"' then the pre-authentication unprivileged process is subject to additional restrictions. The default is "sandbox".

X11Forwarding

X11Forwarding

PermitRootLogin

Specifies whether root can log in using ssh. The argument can be:

  • "yes" (default)
  • "no"
  • "prohibit-password", "without-password": Password and keyboard-interactive authentication are disabled for root.
  • "forced-commands-only": root login with public key authentication is allowed, but only if the command option has been specified. This may be useful for taking remote backups even if root login is normally not allowed. All other authentication methods are disabled for root.

MaxAuthTries

Specifies the maximum number of failed authentication attempts per connection after which additional failures are logged. Default is 6.

StrictMode

Specifies whether sshd should check file modes and ownership of the user's files and home directory before accepting login. The default is "yes". Note that this does not apply to ChrootDirectory, whose permissions and ownership are checked unconditionally.

PubkeyAuthentication

Specifies whether public key authentication is allowed. The default is yes.

AddressFamily

Specifies which address family should be used by sshd: "any" (default), "inet" (use IPv4 only) and "inet6" (use IPv6 only).