VirtualBox Virtual Machine Creation
Internal
Linux
VM Creation
From the VirtualBox Manager -> New -> Expert Mode (it may already start in Expert Mode, and in that case, you'll see a button named "Guided Mode" at the bottom of the screen).
The VM creation process with create the corresponding files in a directory associated with the VM, in ~/VirtualBox VMs/<vm-name>.
The VID (VirtualBox disk image) is a file with .vdi extension.
Name master31-1.openshift.local
Type Linux
Version Red Hat (64-bit)
Memory Size Choose as appropriate. Always keep in mind the amount of physical memory available to your hypervisor, and how many VMs you plan to use at the same time.
Create a virtual hard disk now
Create
File Location Will default to the VM name and that is appropriate. The corresponding physical file will get a .vdi extension and it will be available as ~/VirtualBox VMs/<vm-name>/<vm-name>.vdi
File size A typical minimal RHEL 7.2 takes about 1.6GB.
Hard disk file type VDI (VirtualBox Disk Image)
Storage on physical hard disk Dynamically allocated
Create
After this step, the VM should be created and you can review configuration in the right pane.
If you plan to manage this VM as part of a group, now is the time to create the VirtualBox group and move the VM in it.
Virtual Hardware Configuration
Note
- Click OK often, if you go through many changes and successive tabs and don't click OK, Cancel will discard all changes.
Select the newly created VM -> Right click -> Settings
System
System -> Motherboard
Boot Order Optical, Hard Disk (deselect Floppy)
Chipset ICH9
Pointing Device USB Tablet (this is important, default "PS/2 Mouse" does not handle well cursor transition between windows and you will need to Left Command to release the mouse.
Extended Features
- Enable I/O APIC
- Hardware Clock in UTC Time
System -> Processor
Processors(s)
Execution Cap 100%
Extended Features Enable PAE/NX
System -> Acceleration
Paravirtualization Interface Default
Hardware Virtualization
- Enable VT-x/AMD-v
- Enable Nested Paging.
Display
Display -> Screen
Video Memory 128 MB
Monitor Count 1
Scale Factor 100%
HiDPI Support Use Unscaled HiDPI Output
Display -> Remote Display
Display -> Video Capture
Storage
Settings -> Storage
Controller IDE
Attributes
Name IDE
Type ICH6
Use Host I/O Cache
Empty -> Leave it IDE Secondary Master.
No Live CD/DVD
Controller SATA
Attributes
Name SATA
Type AHCI
Port Count 1
Use Host I/O Cache
<vm-name>.vdi
Attributes
Hard Disk SATA Port 0
Solid-state Drive (if it's a Solid-state Drive)
Network
See VirtualBox Networking Concepts for clarifications. Usually we we want to add one Host-only adapter and one NAT adapter (in this order).
Before adding the Host-only network adapter, go to VirtualBox -> Preferences -> Network -> Host-only Networks and add a Host-only network, if required. If one already exists and you plan to share it, you're all set. If there isn't any, add "vboxnet0". Configure it as described here: VirtualBox Host-Only Networking Configuration.
Settings -> Network
Edit "Adapter1" and "Adapter2". Adapter1 should be Host-only and Adapter2 should be NAT. For all adapters:
Enable Network Adapter
Attached to: Host-only Adapter, then NAT
Advanced
Adapter Type Paravirtualized Network (virtio-net)
Promiscuous Mode Deny
MAC Address use default
Cable Connected yes
Save the Hardware Configuration
At this point, the virtualized hardware configuration is defined, save it.
Clone VMs with Identical Hardware
If we are going to create more virtual machines with the same hardware configuration, now is the moment to clone them.
Right click on the newly created VM -> Clone
Give it the appropriate name.
Clone Type: Full Clone
Snapshots: Current machine state
Reinitialize the MAC address of all network cards
Linux Guest OS Installation
Select the VM -> Settings -> Storage -> Controller: IDE -> Select drive -> Attributes: Optical Drive: IDE Secondary Master -> click on the Disk icon on the right -> Choose Virtual Disk File -> Select the OS iso file -> OK.
Select the VM -> Right click -> Start -> Normal Start.
The Linux installation program should start. From now on go to RHEL 7.2 Installation to perform the guest OS installation.
When the OS installation is done, continue with Guest Additions.
Guest Additions
The guest additions are special software packages that are shipped with VirtualBox but designed to be installed inside a VM to improve the performance of the guest OS and add extra features.
Guest Additions are supposed to be installed inside the virtual machine after the guest operating system has been installed. They are shipped as a CD ISO http://download.virtualbox.org/virtualbox/5.0.4/VBoxGuestAdditions_5.0.4.iso.
Download VBoxGuestAdditions_5.0.4.iso from the same place the hypervisor was downloaded from, then mount the image as a local filesystem: Select the VM -> Settings -> Storage -> Controller IDE -> Disk icon -> Choose Virtual Optical Disk File
Content is found on the guest system as /dev/disk/by-label/VBOXADDITIONS_5.0.4_102546.
Mount it:
mount /dev/disk/by-label/VBOXADDITIONS_5.0.4_102546 /mnt
Installation as root:
yum -y install bzip2 kernel-devel gcc cd /mnt ./VBoxLinuxAdditions.run
Reboot to Make Sure the Host Starts
Reboot and make sure the host starts.
!!!Windows VM Creation
Lessons learned so far:
- The screen resolution does not seem great and the mouse interaction is choppy.
- It is probably best if I access it over Remote Desktop
- Some way to exchange files/
__Referenced by:__\\ [{INSERT com.ecyrd.jspwiki.plugin.ReferringPagesPlugin WHERE max=20, maxwidth=50}]