OpenShift 3.5 Installation: Difference between revisions

From NovaOrdis Knowledge Base
Jump to navigation Jump to search
Line 77: Line 77:
</pre>
</pre>


Reboot the system to make sure it starts correctly after package installation:


<pre>
systemctl reboot
</pre>





Revision as of 19:08, 22 May 2017

External

Internal

Overview

There are two installation methods: quick install, which uses a CLI tool available in the "atomic-openshift-utils" package, which, in turn, uses Ansible in the background, and advanced install. The advanced install assumes familiarity with Ansible. This document covers advance install.

Prerequisites

External DNS Setup

An external DNS server is required.

Procedure to configure a bind server:

Set up a bind Server

Minimum Hardware Requirements

https://docs.openshift.com/container-platform/3.5/install_config/install/prerequisites.html#hardware

A full Master installation requires ... GB of disk.

O/S Requirements and Configuration

https://docs.openshift.com/container-platform/3.5/install_config/install/prerequisites.html
https://docs.openshift.com/container-platform/3.5/install_config/install/host_preparation.html

Install RHEL 7.3 in "minimal" installation mode. A possible way to install it is on top of a VirtualBox virtual machine, as described here.

OpenShift requires NetworkManager on all nodes (see https://docs.openshift.com/container-platform/3.5/install_config/install/prerequisites.html#prereq-networkmanager). Using NetworkManager, assign a static IP address to the interface to be used by the OpenShift cluster, as described here: adding a Static Ethernet Connection with NetworkManager.

Turn off sshd client name DNS verification.

Attach the node to the subscription, using subscription manager, as described here: registering a RHEL System with subscription manager then follow the specific subscription steps required by OpenShift: https://docs.openshift.com/container-platform/3.5/install_config/install/host_preparation.html#host-registration

Sequence of steps - the goal of these steps is to configure the following supported repositories on the system: "rhel-7-server-rpms", "rhel-7-server-extras-rpms", "rhel-7-server-ose-3.5-rpms", "rhel-7-fast-datapath-rpms":

subscription-manager register
subscription-manager list --available --matches '*OpenShift*'
subscription-manager attach --pool=<pool-id> --quantity=1
subscription-manager repos --disable="*"
subscription-manager repos --list-enabled
yum repolist
yum-config-manager --disable <repo_id>
subscription-manager repos --enable="rhel-7-server-rpms" --enable="rhel-7-server-extras-rpms" --enable="rhel-7-server-ose-3.5-rpms" --enable="rhel-7-fast-datapath-rpms"
subscription-manager repos --list-enabled
yum repolist

Install base packages (https://docs.openshift.com/container-platform/3.5/install_config/install/host_preparation.html#installing-base-packages):

yum install wget git net-tools bind-utils iptables-services bridge-utils bash-completion
yum update
yum install atomic-openshift-utils

Prevent accidental upgrades of OpenShiift and Docker, by installing "excluder" packages. The *-excluder packages add entries to the "exclude" directive in the host’s /etc/yum.conf file when installed. Those entries can be removed later when we explicitly want to upgrade OpenShift or Docker. More details in yum Exclusion.

yum install atomic-openshift-excluder atomic-openshift-docker-excluder

If later we need to upgrade, we must run the following command:

atomic-openshift-excluder unexclude

Reboot the system to make sure it starts correctly after package installation:

systemctl reboot






Register all hosts with Red Hat Subscription Manager to RHEL 7.x and OpenShift 3 repositories.

Extra packages required:

yum install wget git net-tools bind-utils iptables-services bridge-utils bash-completion
yum update -y

Turn off firewalld and configure the iptables service

  • Make sure master can issue remote commands on the nodes without requiring password. Ansible, who runs the installation process, requires a user that has password-less access to all hosts.

From the master, as root:

# ssh-keygen
# ssh-copy-id root@node1.example.com
  • Configure iptables. iptables must be running and the following ports must be open. Most of the ports will be configured by the installer, automatically - verify that.:
OpenShift Ports

Install Docker

A Docker that works with OpenShift must be installed from rhel-7-server-ose-3.2-rpms and have it running on master and all nodes before installing OpenShift. Version requirements are specified in Prerequisites.

yum install docker

Edit /etc/sysconfig/docker and add:

OPTIONS=--selinux-enabled --insecure-registry 172.30.0.0/16

--insecure-registry instructs Docker daemon to trust any Docker registry on 172.30.0.0/16 subnet without requiring a certificate.

The default loopback storage is not appropriate for production, it should be replaced by a thin-pool logical volume. Use the docker-storage-setup script:

  • The script reads configuration options from /etc/sysconfig/docker-storage-setup.
  • Reinitialized Docker before starting docker-storage-setup:
systemctl stop docker
rm -rf /var/lib/docker/*
  • Execute docker-storage-setup to create thin-pool volume free space in the volume group where the root filesystem resides.
  • Use the existing volume group to create thin-pool:
# cat /etc/sysconfig/docker-storage-setup
DEVS=/dev/vdb
VG=docker-vg
# docker-storage-setup

TODO B3cEwd.

Generic installation instructions:

Docker Installation

Run CLI to Install

Post-Install

Deploy the Integrated Docker Registry

Deploy the HAProxy Router

Load Image Streams

Load Templates

Set up NFS

The NFS server is required for persistent volumes.

Advanced Installation

OpenShift Advanced Installation

TODO

DNS Configuration

After setup, the DNS server needs to be configured to resolve a public wildcard DNS entry to the public IP address of the node that executes the default router, by adding an A record, with a low TTL. If the environment has multiple routers, an external load balancer is required.

*.myapp.example.com. 300 IN  A 1.2.3.4

Also see https://docs.openshift.com/container-platform/3.5/install_config/install/prerequisites.html#wildcard-dns-prereq