Iptables Command Line Tool

Internal

• iptables

Overview

iptables is a Linux userspace command line tool that manipulates the IPv4 filtering rules. The IPv6 equivalent is ip6tables. The tools can be used to list the rules loaded in memory and add and remove rules. All the changes only reflect in memory and won't survive a reboot, unless the associated service's configuration files are correspondingly updated.

iptables always targets the "filter" table by default. In order to change the target table, use the -t <table-name> options.

Commands

List Rules

Tactical:

iptables -L -v

More details:

iptables -L -nv --line-numbers

The command list all rules in the selected chain. If no chain is selected, all chains are listed.

The command applies to the specified table ("filter" is the default). If you need to list rules from a table other than "filter", use -t (example -t nat).

The command is often used with the -n option, in order to avoid long reverse DNS lookups.

Add a Rule to the Default Table

iptables -A <chain> -i <interface> -p <protocol> -s <source>  [-m <module> <module-config>] -j <target>

The rule will only be added in memory

The rule will only be added in memory and won't survive a reboot. In order to make the rule permanent TODO.

The rule will be added at the bottom of the chain

By default, the rule will be added at the bottom of the chain, after the last existent rule. This means that all existent rules will be evaluated before a packet reaches the newly added rule, so if there's a previous rule that discards the packet, the newly added rule might never be exercised. For that, you may want to consider inserting the rule at a specific position in the chain. See #Insert_a_Rule_into_the_Default_Table.

The rule will be added to the "filter" table

The rule will be added to the "filter" table. If you need to add the rule to a different table, use -t.

Chain

The target chain is specified with -A. It can be one of INPUT, OUTPUT, FORWARD, PREROUTING and POSTROUTING.

Interface

The network interface to apply the rule to is specified with -i. It must be one of your existing network interfaces (example "eth0"). If -i is not specified, the rule applies to all interfaces.

Protocol

The protocol to apply the rule to is specified with -p. It must be one of the known protocols, such as "tcp" or "udp". To specify the rule applies to all protocols, use -p all. If -p is not specified, the rule applies to all protocols.

Source

The source specification:

-s, --source address[/mask][,...]

Address can be:

• a network name TODO example
• a hostname TODO example
• a network IP address (with /mask) TODO example
• a plain IP address. TODO example

Hostnames will be resolved once only, before the rule is submitted to the kernel, but specifying any name to be resolved with a remote query such as DNS is a really bad idea.

The mask can be either an ipv4 network mask (for iptables) or a plain number, specifying the number of 1's at the left side of the network mask. Thus, an iptables mask of 24 is equivalent to 255.255.255.0.

A "!" argument before the address specification inverts the sense of the address.

The flag --src is an alias for this option. Multiple addresses can be specified, but this will expand to multiple rules (when adding with -A), or will cause multiple rules to be deleted (with -D).

For usage examples, see an example allowing incoming connections only from host on a specific subnet.

Module Configuration

-m stands for module and it is used to specify module-specific configuration. See the #Modules section for more details.

TODO

Target

-j stands for jump and it is used to specify the rule's target: ACCEPT, REJECT, DROP, etc.

Example of allowing external HTTP access on a specific interface:

iptables -A INPUT -i enp0s25 -p tcp -j ACCEPT

Integrate this:

!!!Adding a Rule

Note that the [rules|iptables#FirewallRule] are evaluates in the order in which they're added: the first rule that is added is evaluated first, etc.

{{{

   iptables -A <chain> -i <interface> -s <source> -p <protocol> [-m <module> <module-config>] -j <target>

}}}

where:

-i stands for interface.

-p stands for protocol.

--sport - stands for source port.

--dport - stands for destination port.

__Note__: In order to use matches such as destination or source ports (--dport or --sport), you must first specify the protocol (tcp, udp, icmp, all).

-s (--source, --src) stands for source. It accepts a {{[[!] <address>[[/mask]}} source specification. Address can be either a network name, a hostname (please note that specifying any name to be resolved with a remote query such as DNS is a really bad idea), a network IP address (with /mask), or a plain IP address. The mask can be either a network mask or a plain number, specifying the number of 1s at the left side of the network mask. Thus, a mask of 24 is equivalent to 255.255.255.0. A "!" argument before the address specification inverts the sense of the address.

!!Examples

Example of adding a rule that allows all packets coming from the local interface:

{{{

   iptables -A INPUT -i lo -j ACCEPT

}}}

Insert a Rule into the Default Table

Use -I instead of -A and also specify the rule number:

iptables -I <chain> <rule-number> ...

If the rule number is 1, the rule or rules are inserted at the head of the chain. This is also the default if no rule number is specified.

Commit

TODO

After adding and testing a rule, must commit, otherwise the rule will be lost upon Template:Iptables restart!

Setting the Default Policy of A Chain

iptables -P <chain-name> <default-policy>

Example

iptables -P INPUT DROP

Flushing All Rules

iptables -F

Note this does not change the default policy of the chains.

Delete a rule

iptables -D <chain> <rule-number> ...

Modules

state

Reads the connection state and can be used to express conditions based on the connection's state.

For example, to specify that only the new connections are allowed, use this configuration:

-m state --state NEW

More details are available here:

iptables State Module

mac

Reads the MAC address.

tcp

Allows specification of TCP-related configuration.

For example, to identify TCP connections to port 80, use the following configuration:

-m tcp --dport 80

iptables Command Line Tool Examples

iptables Command Line Tool Examples