Dell iDRAC and LifeCycle Controller Configuration: Difference between revisions
(Created page with "=Internal= * Dell Servers#Subjects") |
|||
| (23 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=External= | |||
* Setting Up Your Dell PowerEdge Server Using Dell Lifecycle Controller http://www.dell.com/support/Manuals/us/en/19/poweredge-r630/Sys_Mgmt_GSG | |||
=Internal= | =Internal= | ||
* [[Dell Servers#Subjects]] | * [[Dell Servers#Subjects|Dell Servers]] | ||
=Overview= | |||
This is the procedure to configure [[Dell_Server_Concepts#iDRAC|iDRAC]] and [[Dell_Server_Concepts#LifeCycle_Controller|Dell LifeCycle Controller]] upon the first access, and then configure it in case further configuration changes are needed. The LifeCycle controller can be accessed at boot by pressing F10 during the boot sequence. | |||
=Configuration= | |||
==iDRAC Network Configuration== | |||
LifeCycle Controller Home -> Left Menu -> System Setup -> Advanced Hardware Configuration -> iDRAC Settings -> Network | |||
Enable NIC: enabled | |||
NIC Selection: LOM4 | |||
IPv4 Settings. | |||
==LifeCycle Controller Network Configuration== | |||
LifeCycle Controller Home -> Left Menu -> Settings -> Network Settings | |||
NIC Card. Use the last one. | |||
IPv4 Network Settings | |||
{{Warn|I noticed that the LifeCycle controller network settings did not take - or did partially take - after an initial setup, so it is a good idea to check the Settings after reboot.}} | |||
=Initial Setup Procedure= | |||
{{Warn|I noticed that the LifeCycle controller network settings did not take - or did partially take - after an initial setup setup, so it is a good idea to check the Settings after reboot, following the [[#Configuration|Configuration]] details, below.}} | |||
====Step 1==== | |||
Set Language and Keyboard Type. | |||
====Step 3==== | |||
Assign one of the network cards present on the system to LifeCycle controller, and give it an IP address. | |||
Choose the last network interface (em4), assign 192.168.1.11. | |||
====Step 4==== | |||
The network interface to use for iDRAC can be selected in Advanced Settings page -> Network. | |||
By default is LOM1. | |||
If you intend to change it to LOM4, perform this change first before assigning the IP address, changing the network card after assigning the IP address will discard IP address settings. | |||
Then set up iDRAC network configuration and credentials. Assign the next IP address after the one assigned to the LifeCycle controller. | |||
====Step 5==== | |||
Summary, iDRAC and LifeCycle Controller should have successive IP addresses. | |||
Latest revision as of 21:36, 24 June 2017
External
- Setting Up Your Dell PowerEdge Server Using Dell Lifecycle Controller http://www.dell.com/support/Manuals/us/en/19/poweredge-r630/Sys_Mgmt_GSG
Internal
Overview
This is the procedure to configure iDRAC and Dell LifeCycle Controller upon the first access, and then configure it in case further configuration changes are needed. The LifeCycle controller can be accessed at boot by pressing F10 during the boot sequence.
Configuration
iDRAC Network Configuration
LifeCycle Controller Home -> Left Menu -> System Setup -> Advanced Hardware Configuration -> iDRAC Settings -> Network
Enable NIC: enabled
NIC Selection: LOM4
IPv4 Settings.
LifeCycle Controller Network Configuration
LifeCycle Controller Home -> Left Menu -> Settings -> Network Settings
NIC Card. Use the last one.
IPv4 Network Settings
I noticed that the LifeCycle controller network settings did not take - or did partially take - after an initial setup, so it is a good idea to check the Settings after reboot.
Initial Setup Procedure
I noticed that the LifeCycle controller network settings did not take - or did partially take - after an initial setup setup, so it is a good idea to check the Settings after reboot, following the Configuration details, below.
Step 1
Set Language and Keyboard Type.
Step 3
Assign one of the network cards present on the system to LifeCycle controller, and give it an IP address.
Choose the last network interface (em4), assign 192.168.1.11.
Step 4
The network interface to use for iDRAC can be selected in Advanced Settings page -> Network.
By default is LOM1.
If you intend to change it to LOM4, perform this change first before assigning the IP address, changing the network card after assigning the IP address will discard IP address settings.
Then set up iDRAC network configuration and credentials. Assign the next IP address after the one assigned to the LifeCycle controller.
Step 5
Summary, iDRAC and LifeCycle Controller should have successive IP addresses.